How To Repair Sideboard Of Bed Frame

Download Article

Download Article

Knowing how to paint a metal bed frame is important when you want to update your sleeping accommodation with a new color scheme, repair damage or totally refinish an former or re-cycled metal bed frame. With a few basic tools and some time and patience, painting that bed frame is a project anyone can do. At that place are two methods of refinishing metal bed frames, with spray paint or with a brush.

Choose to spray-paint your bed frame if the frame is in fairly proficient shape already, and information technology just needs a simple one-color paint task and does not take fancy details like embossed or raised designs on information technology.

1. ane

   Find a good spot for painting.

   • This needs to be a well-ventilated identify, dry out, with temperatures between 45°F and 85°F (vii°C and 29°C).
   • It should be fairly dust and insect free and where children and pets won't disturb the bed frame equally the paint dries.
   • There should be something in the area where parts can be propped confronting every bit you pigment them and as they to dry. You could apply a sawhorse, ladder or an old chair for this. You could likewise tape a driblet material to a wall and lean the bed frame against that.

2. two

   Take the metal bed frame apart equally much equally you can. Every bit you work, pay attention to how the frame was assembled and so you lot tin re-get together information technology correctly. Shop the nuts and bolts and other small-scale hardware in a secure container.

   Advertisement

3. 3

   Wash the bed frame pieces with hot water and dish detergent and wipe them dry. Pay attention to corners, and crevices in designs. Make sure all the dirt is scrubbed off.

4. iv

   Sand the entire metal frame with medium-fine sandpaper.

   • Whatsoever onetime paint needs to be roughed up and all rust needs to exist removed.
   • Yous may need coarser sandpaper or a wire brush for heavily rusted areas to get-go but stop with the medium fine sandpaper.
   • All loose peeling pigment needs to be removed only it's not necessary to remove all of the paint.

5. five

   Clean whatsoever grit and rust or paint chips thoroughly from the area before y'all commencement painting. Cover the painting area with drib cloths or old newspapers.

6. vi

   Get over the frame with a tack cloth (institute in hardware stores) to remove any particles left from sanding.

7. 7

   Go over the bed frame again with a damp, soft material.

8. 8

   Accommodate the bed frame pieces against your prop (sawhorse, wall).

9. 9

   Spray the frame with a metal paint primer.

   • When one surface is dry, flip the pieces and spray the other side.
   • Use dull, sweeping motions with the spray tin can and avoid heavy coats that make drips.
   • Allow the primer to dry completely before moving on to the next step.

10. x

    Spray the metal bed frame with paint.

    • This paint should exist rust resistant, and made for utilize on metallic.
    • Utilise those smooth, steady sweeping motions to get even coverage.
    • Let the outset surface dry completely, so turn the pieces and spray the other side.

11. 11

    Employ a second glaze of paint just like the starting time. Pay attention to corners and design areas to make certain they don't collect excess paint or remain unpainted.

12. 12

    Allow the frame dry and apply a third coat if you want a smoother finish.

13. 13

    Button the screws or bolts from the frame into a cardboard box, heads on the surface, and spray them with pigment and then the heads will match the frame color. Allow dry.

14. 14

    Use a coat of articulate sealer to the bed frame to ensure the longest wear and let it to dry.

15. 15

    Re-get together the metallic bed frame.

    Advertisement

Paint your metal bed frame with a brush if you have a respiratory condition that might worsen from inhaled spray particles or fumes. You will likewise want to use a castor to paint the frame if you are painting on a blueprint (e.g., making stripes or adding flowers). If the frame has a lot of ornate designs like scrolls, mitt painting will give you better coverage and crisper particular.

1. ane

   Follow the steps in a higher place to prep the metal bed frame for painting. ^[1]

2. 2

   Brush on a coat of metallic paint primer. Apply shine strokes and don't overload the paintbrush to avoid runs and drips.

3. 3

   Let the surface dry and then flip the pieces over and paint the other side of each. Let dry.

4. 4

   Castor on an acrylic or oil-based paint for metal using smooth, steady stokes, and avoiding drips and runs. Let one side dry out, flip pieces and paint the other side.

5. v

   Apply a 2d coat of pigment as to a higher place when the kickoff is dry. Check the paint label to see how long to let the paint dry between coats. A third glaze may be needed with some paints.

6. six

   Paint on designs like flowers or stripes after the concluding glaze of paint has dried and let the details dry.

7. 7

   Paint the heads of screws and bolts as described above, except using a brush. This procedure will allow you to incorporate more details if you wish.

8. eight

   Utilise a coat of clear paint sealer to the bed frame later all the pigment layers take dried.

9. nine

   Let the paint sealer dry before re-assembling the metal bed frame.

   Advertisement

Add New Question

• Question

  What should I practice if the spray paint runs?

  

  Immediately wipe off the run and re-spray information technology right then and there. If the piece was left to dry out and you didn't wipe it in fourth dimension, then you'll need to scrape off the bulk and sand the area perfectly apartment and polish to its environment for a paint touch on-up.

• Question

  I take a new metal bed and I want to pigment it. Exercise i nevertheless need to sandpaper it before I begin?

  

  Aye. It helps the paint stick. If yous don't sand it, the smooth surface of the pigment underneath tin can cause bug.

• Question

  I was spray painting my metal futon and many drips dried. I had to sand them down. In the future, how do i preclude that from happening?

  

  Brett Gilbert

  Top Answerer

  It's usually from adding too much paint at once. Some of it doesn't stick in place, so it drips. Try moving the canister at a faster charge per unit. Aim on applying a lite but even coat of paint. And then, wipe up drips as shortly as you notice them.

Ask a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Advert

• Have several sizes of paintbrushes when hand painting a bed frame so all areas tin can be painted efficiently.

• Employ a strong toothbrush to clean dirt or rust out of crevices.

• Motorcar polish tin be used in place of clear sealer to protect bed frames.

• Equally you take apart the bed frame check the screws or bolts to see if the threads are worn or the heads are damaged and replace them.

• Sanding the frame in a location unlike from where it is painted helps continue grit and pigment chips away from the painted surface.

Thanks for submitting a tip for review!

Advertisement

• Make sure to buy pigment that is recommended for metal. Latex and some other paints volition not work well.

• Vesture goggles when spray-painting.

• Repainting over brass is non easy and should be left to professionals. Contumely is better polished than repainted.^[2]

• Ever paint in a well-ventilated room and wear a painting mask. Fans can help disburse paint fumes.^[3]

• Article of clothing a mask when sanding if the pigment may be old pb-based paint. Anyone with asthma or other respiratory problems may besides want a mask when sanding.^[iv]

Advertisement

Things Yous'll Need

• Screwdriver, pliers, wrenches and other tools for taking apart the bed frame
• Driblet clothes or old newspapers
• Medium fine sandpaper
• Tack textile
• Clean soft cloths
• Dish lather
• Metal paint primer
• Metal paint
• Pigment brushes if manus painting
• Painting masks
• Goggles
• Minor cardboard box for painting screw and bolt heads.

Most This Article

Cheers to all authors for creating a page that has been read 262,828 times.

Did this article help you?

Source: https://www.wikihow.com/Paint-a-Metal-Bed-Frame

Posted by: gibbonshising.blogspot.com

Share this post